中文 | English
Layout Domestic And International Markets & Build International Influence

Common fault maintenance of laser marking machine

Date：2017-07-17Hits：40379

1. malfunction
Turn on the key, the switch doesn't respond 
Turn on the key, the switch doesn't respond
1) the power supply is out of phase or out of phase; 
2) the air switch is not closed; 
3) the emergency stop switch is pressed. 
processing method
1) restore the power supply; 
2) closed air switch; 
3) turn off the emergency stop switch.

2. 故障现象
不能达到预期的打标深度 
原因分析
1） 标刻物件不在聚焦面； 
2） F-θ透镜被污染； 
3） 软件参数不对； 
4） 软件输出异常。 
处理方法
1） 调整焦距； 
2） 清洗F-θ透镜； 
3） 重新调整参数； 
4） 重启软件。

 
3. 故障现象
开软件时，弹出“无法找到控制卡，……”提示 
原因分析
1） 控制没有上电； 
2） USB连接线松的； 
3） 卡的驱动是否没有安装好； 
4） USB控制卡损坏。 
处理方法：
1） 检查钥匙开关是否打开，开关电源是否无输出； 
2） 检查USB连接线； 
3） 重新安装版卡的驱动； 
4） 更换控制卡。

4. malfunction
No laser output
Reason analysis
1) software settings are normal;
  2) power key is open;
  3) USB control card red light flashing;
  4) internal faults of laser power supply or laser.
processing method
1) check the software settings;
  2) turn key;
  4) please contact our technical staff.

 
5. malfunction
A graphic or literal distortion or distortion 
Reason analysis
1） 软件没有进行矫正，或者数据丢失； 
2） 振镜电源供电不对； 
3） 信号干扰； 
4） 控制板卡有问题； 
5） 振镜故障。 
1) software is not correct, or loss of data;
2) mirror power supply fault;
3) signal interference;
4) there are problems of control card;
5) vibration mirror fault.
processing method
1) parameter adjustment;
  2) adjust the switching power supply voltage, or replacement;
  3) to confirm the reliability of grounding signal line is bad;
  4) replace the control board;
  5) replace the galvanometer.		  

 

 

 

 

 

 

 

 

 

Return list
Frequently Questions

How is laser processing technology carried out?

Laser processing technology is the technology of cutting, welding, surface treatment, punching and micro machining of materials (including metal and nonmetal) by the interaction of laser beam and material. Laser technology is a comprehensive technology which involves many subjects, such as light, machine, electricity, material and detection.

Date：2017-07-17 Hits：39395

What should operators pay attention to when using laser products?

Answer: professional laser equipment belongs to the products, the operator must pay attention to the following points: 1. the use of laser equipment operating personnel must be trained, reached a certain level, and on the premise of security administrator with permission to mount guard operation; 2. laser equipment operator or close to the laser in use during the personnel should wear the appropriate laser protective goggles and protective clothing, wear protective glasses in the region, there must be a good indoor illumination, in order to ensure the smooth operation of the operator. In order to protect the operator, it must be equipped with machining, protection, screen and so on. There shall be laser diffusion protection in the processing room

Date：2017-07-17 Hits：39840

Laser products may cause damage to the human body. How should we protect it during use?

The laser beam is a kind of high brightness, high power, high energy, strong laser irradiation on human skin caused by burns, if directly into the eye, or in a light (mirror like) surface reflection can also be caused by injury, will cause permanent damage to the eyes until blindness. Therefore, you should avoid putting any part of your body in the light path of the laser, especially paying attention to the protection of the eyes and skin so as not to cause harm. Different types of lasers do harm to humans differently. In laser processing, CO2 and YAG lasers are most commonly used. YAG laser can damage the retina of the eye

Date：2017-07-17 Hits：39761

Why does fiber laser cutters not emit light?

If the laser cutting machine does not emit light, it will not be able to use the laser to cut the material. It will have a great impact on our production and processing. Therefore, we must check why the fiber laser cutting machine does not emit light, and reduce the failure of the fiber laser cutting machine, causing our economic losses. So, what causes fiber laser cutting machines not to emit light? 1, through the observation of fiber laser cutting machine current meter, check whether the current instruction, if there is no current instructions, fiber laser cutting machine of circuit should be checked; 2, check the fiber laser cutting machine water circulation

Date：2017-07-17 Hits：52704